Exactly How to Remove and Change a Tub
Exactly How to Remove and Change a Tub
Blog Article
This article in the next paragraphs pertaining to How to Install a Bathtub Yourself is amazingly insightful. Read it for your own benefit and decide what you think about it.
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old tub is easily obtainable, the project can move rapidly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the task as well as fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have already bought a new tub and do not require to transform the setup of your previous water pipelines.
Your tools as well as material checklist should comprise the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite problematic as a result of the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the level reads level.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the tub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been made use of at the very least once as this will settle it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in place between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, resulting in problems with wetness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill up the bathtub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can split fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very excited about Tools You Need to Install a New Bathtub and I am praying you appreciated my page. If you appreciated our blog post kindly remember to share it. Thank you for going through it.
Apply Now
Report this page